Nuevo

Kit de reparación de postes de HP41c

N.º de producto: Lower Post Repair Kit

En existencias

Precio anterior 70,00 €
Precio 40,00
El precio incluye el IVA
Suma de los distintos precios 53,80 €


Formas de entrega disponibles: Carta, Small item outside EU, Entrega Canarias/Baleares, Overseas traceable

Lower Post repair

Material needed

  • Lower post repair piece
  • Clothes' peg
  • Keyboard support for clothes' pegs

Let's assume that both posts are broken or cracked. The effect of this cracking is that the screws do not do their job. Usually, using longer screws may help, but this typically is short lived since the cracks will continue downwards. Once the pressure between both halves is softened, the calculator doesn't work anymore. The solution is to repair the broken posts. 

Old methods to repair broken post is to glue them (but this doesn't hold together too long) and to tie them down with very small gauge copper cable, applying pressure so that it holds together. This may solve some cases, but not when the screw path has been destroyed - maybe due to strong tightening of the screws.

Other repair methods have been proposed, including drilling down the screw and placing in its place a cylinder with screw path, glued in place. We tried this method but there was a problem: the torque used to screw resulted in cracked glue and the cylinder separating from the substrate - every time.

Our method was devised with three goals in mind:

  1. Try to avoid the torque from the screw forcing on the glue with the substrate
  2. Try to ensure that the front part of the calculator is pulled up when screwing the back side on.
  3. Try to be compatible with all known zebra connectors - including our own.

The piece that we have designed requires drilling the old posts to the keyboard ciruit level, taking care of leaving the hole clear. The design on the piece is such that the pin will be glued to the inner part of the rest of the screw post; and the surface of the piece can be glued to the keyboard circuit, so that the torque on the substrate is avoided (it also helps that torque is also resisted by the other post, when using the full piece)

ZPN_foto_v2

When gluing the piece, there are several precautions that need to be taken:

  • Be sure of covering the zebra circuit part with tape -we don't want the glue to cover it.
  • Cover also all nearby pin holes of the keyboard. If glue comes into one such hole, the key will not register. In severe cases, the key will be down all the time, glued in place!
  • When applying pressure, use clothes' pegs to hold the piece in place, preferably on the outer side.
  • To avoid pushing the keyboard down, and only push down the front of the calculator, use the keyboard cover we have designed to support the pegs. Pushing the keyboard instead will result on separation between both halves of the calculator, since the attachment of the substrate to the pin will be at a lower level (the keyboard is linked to the keyboard circuit, not to the substrate)
  • Use epoxy glue, type Araldit. 
  • Let it cure overnight.
  • Remove the tape over the zebra circuit paths.
  • Place the zebra connectors
  • Assemble the calculator and test.

We recommend to repair both posts at the same time. However, if you are confident on the resistence of the other post, you can use our 1-side piece. As it is symmetrical, it can be used for both posts, just twisting it 180º. Using the full piece, the other post side does not need to be glued - the torque resistence is done by the post itself over a much longer distance.

Alternatively, you can cut the other side of the 2 post piece with a tweezer and glue in place the rest of the piece.

Información de producto adicional


Se incluyen los siguientes productos independientes

N.º de producto: Zebra PCB

This piece is for repair of HP41c full nut calculator, substituting the damaged or corroded zebra connector that links the main board with the processor circuit. New design.

Black Friday: 20% off

1 unidad(es)
Precio anterior 16,00 €
12,80 *
N.º de producto: keyboard support

Pieza necesaria para la reparación de los postes inferiores de la HP41c

1 unidad(es)
25,00 *
N.º de producto: Lowpostrepair

Pieza para reparar los agujeros para tornillos inferiores de la familia HP41c, del tipo full-nut

1 unidad(es)
16,00 *
* Los precios incluyen el IVA

Accesorios

Producto Nota Estado Precio
Spacer set para reparar HP41c Spacer set para reparar HP41c
10,00 € *
* Los precios incluyen el IVA
Mostrar detalles del accesorio

Los clientes que han comprado este producto también han comprado

Pieza para reparar postes superiores
16,00 *
Módulo conector de baterías y puertos de expansión de HP-41c/cv/cx
44,00 *
Conjunto de tornillos para HP41
3,00 / 4 unidad(es) *
Pieza para reparación de parte trasera de HP41c
17,00 *
Pies para HP41c - pack de cuatro
4,00 / 4 unidad(es) *
Tapa lateral para HP 41c
6,00 *
* Los precios incluyen el IVA

Examine también estas categorías: El Rincón de la HP41, Accesorios, Calculadoras Clásicas, Inicio, HP 41C Repair, Broken lower screw posts